As a car owner, you might want to bypass cranking time exceeded but wonder how to go about it. Fortunately, we have done the research for you, and here is what we found.
Do these to bypass cranking time exceeded:
- Check the battery terminals for corrosion
- Inspect the starter solenoid
- Start your car
An issue with the starter, battery, or ignition system could be to blame if your vehicle takes longer than usual to crank. Bypassing cranking time exceeded is not as difficult as it seems, all you have to do is follow the steps carefully. Keep reading to get detailed information on how to bypass cranking time exceeded.
How Do You Bypass Cranking Time Exceeded?
Here is how to bypass cranking time exceeded:
Check The Battery Terminals For Corrosion
This is the first step to take if you want to bypass cranking time exceeded. When the terminals of a battery become corroded, the energy flow through those terminals will become less efficient. This can cause a decrease in battery power as well as an increase in the amount of time it takes to crank and start the engine.
Battery terminal corrosion can also lead to the destruction of the battery cables over time. It can cause a spark that damages the battery terminal, which in the worst cases, could result in the battery bursting.
As a result of this, you should check and remove any corrosion from your battery terminals. Get rid of any surplus solutions from the battery and clean it thoroughly.
Inspect The Starter Solenoid
During the inspection, check to see if the starter solenoid receives enough power. You can also examine the connections to ensure they are clean and not corroded.
The starter solenoid is a relatively straightforward mechanism that acts as a conduit for the flow of electrical power from the battery to the starter. When you turn the key, the solenoid activates, and the starter starts using the electrical motor it contains to get the engine running.
It is possible that the car will not start if the solenoid is not operating as it should, which could cause the cranking time exceeded error message to come on.
Start Your Car
Make an attempt to start your car. This step is crucial. All you have to do is to start your car while pressing down the accelerator pedal halfway. After this, you have successfully bypassed the cranking time exceeded error. However, if this doesn't work, you can consider the alternative methods of bypassing the cranking time exceeded.
Alternative Methods Of Bypassing Cranking Time Exceeded
Here are other ways to bypass cranking time exceeded:
Use Starting Fluids
Using starting fluid is one of the ways to bypass the crank time exceeded error message. The starting fluid is a flammable liquid that speeds up the rate of combustion for a short period, making it easier to start engines.
To use it, aim the nozzle of the can at the air intake while maintaining a distance of roughly 12 inches (20 centimeters). Spray the engine with the starting fluid for approximately two seconds before starting the vehicle.
After that, if it still won't turn over, spray another two-second burst of starter fluid into the engine and try to start it again.
Crank The Engine Manually
Manually cranking the engine is another option for bypassing cranking time exceeded. This can be done by opening the vehicle's hood and connecting a jumper cable to the starter from the battery. This will eliminate the necessity for the starter to gear the engine.
However, if, despite all these, you are still unable to get the engine started, there is a possibility that the issue is caused by something else entirely. In this particular scenario, getting a professional mechanic's opinion on how to fix the problem is your best bet.
How Long Does Crank Time Exceeded Last?
Cranking time exceeded is a common error code that appears on vehicles. It occurs when an effort to start the car has been made for a total of more than 60 seconds, but the vehicle has not started.
This system is designed to last for approximately 15 minutes to prevent a fuel pump from running dry or having no fuel to lubricate it.
So, even if you have a code reader, you won't be able to reset or clear the code. To get rid of the code, try starting the vehicle again after waiting 15 to 30 minutes (depending on the model).
What Causes Cranking Time Exceeded?
Different problems can lead to a "cracking time exceeded" warning. The following are possible causes:
Battery Problem
This is the most typical cause of cranking time exceeded. If the cables connecting your battery are covered with green or white corrosion, they need to be cleaned or replaced immediately. If not, it could lead to cranking time being exceeded.
Faulty Fuel System
Another cause is an issue with the vehicle's fuel system. If your vehicle's engine cranks slowly and then dies all of a sudden, the problem could be with either the fuel pump or the fuel filter.
A clogged fuel filter will prevent fuel from reaching the engine, which will cause the engine to stall. A defective fuel pump can also cause issues, either by failing to supply the fuel injectors with an adequate amount of pressure or by failing to supply the engine with enough gasoline.
Defective Ignition System
It is possible that there is a problem with the ignition system if the engine of your vehicle turns over slowly at first but then shuts off right away.
The problem could be anything as straightforward as a bad or dirty spark plug connection. So, you might need to replace the spark plug, especially if it's old and worn out.
Additionally, it is possible that there's a problem with the distributor cap or the ignition coil, causing the cranking time to exceed.
Also, your car's sluggish cranking speed and subsequent inability to start could be due to different issues. However, if you are unsure of the nature of the issue, it is in your best interest to take the car to a mechanic for a diagnosis.
A problem with the battery or the fuel system is by far the most prevalent cause, although it might also be an issue with the ignition system.
How Can I Prevent Cranking Time Exceeded?
When the cranking time limit is exceeded, a message will appear in the information display to warn you. When this happens, you will have to wait for some time before attempting to start the vehicle's engine.
To prevent a "cranking time exceeded warning," do the following:
- Ensure you have enough fuel in your car before starting it.
- Check and ensure that your battery terminals are neither loose nor corroded.
- Charge your battery well.
- Ensure the fuel pump is working as expected.
- Ensure the starter solenoid is in good working condition before starting your vehicle.
- Perform routine maintenance on your car.
How Can I Diagnose Cranking Time Exceeded?
Eliminating obvious and inexpensive causes, such as a dead battery or a faulty connection, is the first step in diagnosing the problem. If those aren't the issue, then you need to investigate more.
Possibly the starter motor is failing. If the starter is malfunctioning, the engine will not be able to start since it needs that initial surge of power to get moving.
It is also possible that there's an issue with the gas tank. This engine will not start if fuel is not getting to it. Check each of these things while troubleshooting to narrow down and diagnose the cause.
To Wrap Up
If your car won't start, it could be that the cranking time has been exceeded. This can happen if the battery is low or if the starter isn't getting enough power.
To bypass cranking time exceeded, all you have to do is check the battery terminals for corrosion, inspect the starter solenoid, and start your car. Alternatively, use starting fluid or crank the engine manually. Don't hesitate to contact a professional if you cannot bypass cranking time exceeded alone.
If you enjoyed reading this post, here are similar articles you may like:
How To Crank Engine Without Starting?
F150 Won’t Start Just Turns Over Or Cranks – What Could Be Wrong?